![]() However, our testers could easily use the belt clip to attach it to their belts instead. The only drawback to this tape measure is that it was a bit too bulky to fit in a tool belt. The brand also claims the tape measure can survive up to an 80-foot drop. After dropping it on concrete in our testing lab, our testers found it didn’t have any visible damage. They also noted that they could control the speed of the blade as it fed out and retracted, which prevented the blade from whipping around wildly.ĭuring testing, it had an impressive standout of more than 13 feet, meaning it extended 13 feet from the case before drooping or bending. Our testers found that the case was comfortable to grip, and the lock could be engaged or released with just their thumbs. This 16-foot tape measure is also available in a 25-foot option for longer measurements. The tape measure has stud markings that are conveniently placed every 16 inches. The bright yellow blade features large numbers and double-sided markings. It earned a perfect score during testing across all categories, including performance, durability, accuracy, and value. The Irwin Strait-Line tape measure is our top pick for the best tape measure. Visit our website today to find the tape measure that’s right for your next job.It’s a bit bulky, so it might be a tight fit for a tool belt pouch. Looking for a quality, accurate tape measure? U.S. Once you’ve gotten the tape where you need it to be, take the measurement directly from the tape. If it sags, your measurement will be off. With the hook pressed in place, pull the tape blade out until it spans the distance you’re measuring. If you aren’t measuring something you can latch onto – the distance across a door frame, for example – press the hook against one side to ensure an accurate reading. When using a retractable tape measure, you’ll have a small metal hook at the end of the tape, which you can use to grab onto the edge of what you are measuring to hold the blade in place. Looking at the example, if you measure something past the 28 th centimeter marking to the third millimeter, you would say it measures 28.3 centimeters long. The smallest markings are millimeters, or one tenth of a centimeter.There is a smaller marking exactly halfway between the centimeters for ease of reading.The large, numbered markings are centimeters.If you have a metric tape measure, the numbers should be read like this: There are 10 decimeters in a meter, 10 centimeters in a decimeter, and 10 millimeters in a centimeter. Numbers shown represent meters, decimeters (sometimes shown in red-see example picture), and centimeters. On a metric tape you will basically see markings for meters, centimeters, and millimeters. Most will show fractions down to eighths of an inch. ![]() These are known as ‘Fractional Read’ or ‘Easy Read’ blades. Some tape measures make it easier to decipher the markings by calling out the fractional equivalents right on the face of the blade. For example, the second eighth-inch marking after the inch marking is a quarter inch. Remember that two sixteenths of an inch equals one eighth, two eighths of an inch equals one quarter, and 2 quarters equals one half. On some tapes, quarter inch marks are the same size as eighth-inch marks. These are smaller, sometimes thinner markings, evenly spaced between the half-inch and inch marks on a tape measure. have markings that measure down to 1/16 of an inch. QUARTER INCHES, EIGHTH INCHES, AND SIXTEENTH INCHES ![]() ![]() In other words, the half-inch mark between inches 13 and 14 is read as 13 ½ inches, and sits exactly midway between the markings for those numbers.ģ. Depending on the tape measure, these may not be designated with a number, which means you’ll need the markings on either side to guide you. Half-inch marks sit between two one-inch marks. You will see a foot designation marked every 12 inches (sometimes in a box as in the picture, or sometimes the number will be shown in red). On a tape measure that uses imperial units – as opposed to the metric system – the most prominent markings are typically the inch marks, designated by long, thin lines and larger numbers. Let’s begin by reviewing the essential parts of an “Imperial” or “English” tape measure: In this blog post, we’re going to look at how to accurately read a tape measure. They’re only effective if the person using them knows how to get an accurate reading. That’s an old saying, but a true one, and something that applies to tape measures as well. A tool is only as good as the person using it.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |